Bulletin Number | Vehicle Make | Vehicle Model | Model Year | Summary |
---|---|---|---|---|
05-002-20-3704b | MAZDA | MAZDA3 | 2019 | Some customers may complain about a surging at low speeds and during acceleration. This surging is in the longitudinal direction, felt about 2 cycles |
SA-003-20e | MAZDA | MAZDA3 | 2019 | When the body control module (BCM) has been replaced or reprogrammed and the software is updated to the file names shown below, DTC U2050:55-BCM (Acti |
CSP07_CSP07 | MAZDA | MAZDA3 | 2019 | CSP07 - NON-FUNCTIONING CV AFTER CSP06: ALL DEALERS: If you have a vehicle that came back after CSP06 was repaired, and it does not show CSP07 open i |
SA-012-20e | MAZDA | MAZDA3 | 2019 | 2019-2020 MAZDA3 SERVICE CAUTIONS FOR NEW AND REVISED FEATURES: Connected Vehicle, Connected Vehicle Maintenance Mode, Mazda Connected Vehicle Viewer |
09-011-21-3789 | MAZDA | MAZDA3 | 2019 | Some vehicles (equipped with the Electrical supply unit (ESU) BCKA-67-5Z0B) may exhibit that DTC B2002:49 [BODY CONTROL MODULE (BCM) - Electrical supp |
SA-018-21 | MAZDA | MAZDA3 | 2019 | Some customers or technicians (during PDI) may have concerns with the front doors sticking (especially on hot days) and/or poor appearance, fitment, a |
09-007-21-3751 | MAZDA | MAZDA3 | 2019 | Some vehicles may exhibit that the glass run channel of the front door interferes with the rear door garnish.Since the front door glass run channel is |
02-004-21-3785 | MAZDA | MAZDA3 | 2019 | Some vehicles may exhibit a rattle noise from the front suspension when driving over bumps or on a road with a wavy surface. The noise may be caused b |
15-004-20-3755 | MAZDA | MAZDA3 | 2019 | Some vehicles may exhibit that both sides (right and left sides) of the Blind Spot Monitoring (BSM) and Rear Cross Traffic Alert (RCTA) system do not |
09-013-20-3663 | MAZDA | MAZDA3 | 2019 | When the Telematics Communication Unit (TCU) has been replaced or reprogrammed and the software is updated to ones shown below, DTC U2050:55-TCU (Acti |
09-013-20-3663c | MAZDA | MAZDA3 | 2019 | When the Telematics Communication Unit (TCU) has been replaced or reprogrammed and the software is updated to ones shown below, DTC U2050:55-TCU (Acti |
SA-009-21 | MAZDA | MAZDA3 | 2019 | Some customers may complain that the seat warmer turns off after 10 minutes in manual mode and will not turn back on until the vehicle is restarted. D |
SA-001-21 | MAZDA | MAZDA3 | 2019 | Refer to the Repair Procedure when installing the trunk weatherstrip for guidance, otherwise water may enter the trunk during heavy rain or when going |
09-007-21-3751 | MAZDA | MAZDA3 | 2019 | Some vehicles may exhibit that the glass run channel of the front door interferes with the rear door garnish. Since the front door glass run channel i |
CSP06e | MAZDA | MAZDA3 | 2019 | CSP06 - 2019 MAZDA3 MODULE UPDATE FOR CONNECTED SERVICES. Please review the newest repair procedure updated today, September 25, 2020 that performs 2 |
09-013-20-3663a | MAZDA | MAZDA3 | 2019 | When the Telematics Communication Unit (TCU) has been replaced or reprogrammed and the software is updated to ones shown below, DTC U2050:55-TCU (Acti |
09-033-20-3742 | MAZDA | MAZDA3 | 2019 | Some vehicles may exhibit that DTC B2002:49 will not clear with the Mazda Modular Diagnostic System (MMDS). Applicable vehicles are equipped with the |
09-018-20-3690a | MAZDA | MAZDA3 | 2019 | Some customers may notice white lines appearing across the instrument cluster (as shown below). The white lines may be caused during the production pr |
09-013-20-3663b | MAZDA | MAZDA3 | 2019 | When the Telematics Communication Unit (TCU) has been replaced or reprogrammed and the software is updated to ones shown below, DTC U2050:55-TCU (Acti |
07-005-20-3745 | MAZDA | MAZDA3 | 2019 | Some customers may complain that the A/C blows warm air while idling after restarting a warm engine. This is caused by improper control software of th |
SA-050-20 | MAZDA | MAZDA3 | 2019 | Some vehicles may experience M-MDS (MDARS) showing the front radar dynamic aiming is incomplete although the procedure is completed. This is caused by |
SA-012-20d | MAZDA | MAZDA3 | 2019 | 2019-2020 MAZDA3 SERVICE CAUTIONS FOR NEW AND REVISED FEATURES: Connected Vehicle, Connected Vehicle Maintenance Mode, Mazda Connected Vehicle Viewer |
SA-010-20b | MAZDA | MAZDA3 | 2019 | When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to initialize the new TCU after replacement. Use the infor |
SA-004-20a | MAZDA | MAZDA3 | 2019 | In order to ensure key code security, MNAO has restricted key code access for the new auxiliary key. This Service Alert provides information on how to |
SA-003-20d | MAZDA | MAZDA3 | 2019 | When the body control module (BCM) has been replaced or reprogrammed and the software is updated to the file names shown below, DTC U2050:55-BCM (Acti |
SA-040-20a | MAZDA | MAZDA3 | 2019 | Key Transmitter Power Saving Function: When the key transmitter Power Saving Function is turned ON, transmitter battery power consumption is restricte |
SA-057-20 | MAZDA | MAZDA3 | 2019 | Some customers may complain that the HVAC system blows hot air on occasion (blows cold air, then hot air, then cold air again). The customer may notic |
SA-048-20 | MAZDA | MAZDA3 | 2019 | Some customers may expierience an engine no start condition where the engine will only start by holding the key transmitter over the Start/Stop button |
SA-046-20 | MAZDA | MAZDA3 | 2019 | FSC dynamic aiming (mid-drive aiming) may not complete if the vehicle is driven on a road as described below: ï¿· The road lane mar |
SA-045-20 | MAZDA | MAZDA3 | 2019 | Some customers may complain about a vibration / rattle noise coming from the dash above the instrument cluster. This may be caused by an active drivin |
SA-044-20 | MAZDA | MAZDA3 | 2019 | Some vehicles may display incorrect tire pressures in MAZDA CONNECT. This may be caused by an incorrect calendar entry (month/day/year) after a batter |
SA-043-20 | MAZDA | MAZDA3 | 2019 | Some vehicles may exhibit DTC U2120:00 and/or U2500:82 stored in memory and the i-ACTIVSENSE warning light (amber) ON when turning ON the ignition aft |
CSP06 | MAZDA | MAZDA3 | 2019 | CSP06 - 2019 MAZDA3 MODULE UPDATE FOR CONNECTED SERVICES: On July 6, this campaign was temporarily suspended due to software programming concerns. The |
15-002-20-3719 | MAZDA | MAZDA3 | 2019 | Some vehicles equipped with Smart Brake Support (SBS) may exhibit a front radar system malfunction message in the instrument cluster with DTC C1A67:04 |
09-023-20-3723 | MAZDA | MAZDA3 | 2019 | Some vehicles may exhibit a deformed fuel-filler lid panel (1) attached to the fuel-filler lid box, resulting in a poor appearance. This concern is ca |
07-003-20-3712 | MAZDA | MAZDA3 | 2019 | Some customers may hear a repeating click sound when using the HVAC system. The click sound may be caused by the air mix doors moving back and forth. |
01-009-20-3710 | MAZDA | MAZDA3 | 2019 | Some customers may complain about a very low frequency noise and/or vibration felt at the steering wheel, the floor and/or the seats when driving at 1 |
01-004-20-3684b | MAZDA | MAZDA3 | 2019 | Some customers may experience the master warning light turning on and a lack of power with DTC P2BF6:00 (Exhaust shutter valve position sensor circuit |
SA-029-20g | MAZDA | MAZDA3 | 2019 | Some customers may experience a "IN-VEHICLE NETWORK MALFUNCTION" warning message in the instrument cluster with one or more of the following DTC's sto |
CSP06b | MAZDA | MAZDA3 | 2019 | CSP06 - 2019 MAZDA3 MODULE UPDATE FOR CONNECTED SERVICES: On July 6, this campaign was temporarily suspended due to software programming concerns. The |
CSP06a | MAZDA | MAZDA3 | 2019 | CSP06 - 2019 MAZDA3 MODULE UPDATE FOR CONNECTED SERVICES: On July 6, this campaign was temporarily suspended due to software programming concerns. The |
SA-061-20 | MAZDA | MAZDA3 | 2019 | If you receive a customer concern about the CHECK IN light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, perform the insp |
SA-060-20 | MAZDA | MAZDA3 | 2019 | When replacing the Body Control Module (BCM) in a 2019 Mazda3, it needs to be configured and the instructions in the Workshop manual on MGSS are incor |
SA-059-20 | MAZDA | MAZDA3 | 2019 | During BCM replacement, MDARS may display a Configuration Error warning message. This may be caused by any of the following: "Poor internet connection |
SA-058-20b | MAZDA | MAZDA3 | 2019 | A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Va |
SA-054-20d | MAZDA | MAZDA3 | 2019 | Some customers may experience an engine no start due to low battery voltage on 2019-2020 Mazda3 and 2020 CX30. Inform the customer that Mazda is activ |
SA-014-20a | MAZDA | MAZDA3 | 2019 | On some vehicles, the Commander switch might be inoperative. This could be caused by fuse F13 (15A) being removed instead of F15 (15A) at the factory |
16-003-20-3731 | MAZDA | MAZDA3 | 2019 | Some customers may not be comfortable with being notified of an engine stall due to an error when operating the clutch pedal. When the engine stalls, |
15-002-20-3719 | MAZDA | MAZDA3 | 2019 | Some vehicles equipped with Smart Brake Support (SBS) may exhibit a front radar system malfunction message in the instrument cluster with DTC C1A67:04 |
09-027-20-3703 | MAZDA | MAZDA3 | 2019 | Some customers may complain about a squeaking noise when sliding the front seat. This is caused by a deformed front seat side bolster that rubs on the |
CSP06c | MAZDA | MAZDA3 | 2019 | CSP06 - 2019 MAZDA3 MODULE UPDATE FOR CONNECTED SERVICES: On July 6, this campaign was temporarily suspended due to software programming concerns. The |
09-023-20-3723a | MAZDA | MAZDA3 | 2019 | Some vehicles may exhibit a deformed fuel-filler lid panel (1) attached to the fuel-filler lid box, resulting in a poor appearance.This concern is cau |
SA-054-20a | MAZDA | MAZDA3 | 2019 | Some customers may experience an engine no start due to low battery voltage on 2019-2020 Mazda3 and 2020 CX30. Inform the customer that Mazda is activ |
SA-054-20 | MAZDA | MAZDA3 | 2019 | Some customers may experience an engine no start due to low battery voltage on 2019-2020 Mazda3 and 2020 CX30. Inform the customer that Mazda is activ |
SA-046-20a | MAZDA | MAZDA3 | 2019 | FSC dynamic aiming (mid-drive aiming) may not complete if the vehicle is driven on a road as described below: The road lane markings are covered by sn |
SA-029-20e | MAZDA | MAZDA3 | 2019 | Some customers may experience a "IN-VEHICLE NETWORK MALFUNCTION" warning message in the instrument cluster with one or more of the following DTC's sto |
SA-029-20d | MAZDA | MAZDA3 | 2019 | Some customers may experience a "IN-VEHICLE NETWORK MALFUNCTION" warning message in the instrument cluster with one or more of the following DTC's sto |
SA-0290-20c | MAZDA | MAZDA3 | 2019 | Some customers may experience a "IN-VEHICLE NETWORK MALFUNCTION" warning message in the instrument cluster with one or more of the following DTC's sto |
SA-027-20b | MAZDA | MAZDA3 | 2019 | MAZDA CONNECT Software Version 11002 NOTE: â¿¿2019 Mazda3 owners may notice an icon in their infotainmentâ¿¿s |
SA-010-20d | MAZDA | MAZDA3 | 2019 | When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to initialize the new TCU after replacement. Use the infor |
SA-010-20c | MAZDA | MAZDA3 | 2019 | When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to initialize the new TCU after replacement. Use the infor |
09-021-20-3714 | MAZDA | MAZDA3 | 2019 | Some customers may experience the master warning light and/or the "In-Vehicle Network Malfunction" warning message in the instrument cluster on with D |
05-002-20-3704 | MAZDA | MAZDA3 | 2019 | Some customers may complain about a surging at low speeds and during acceleration. This surging is in the longitudinal direction, felt about 2 cycles |
01-004-20-3684a | MAZDA | MAZDA3 | 2019 | Some customers may experience the master warning light turning on and a lack of power with DTC P2BF6:00 (Exhaust shutter valve position sensor circuit |
05-002-20-3704a | MAZDA | MAZDA3 | 2019 | Some customers may complain about a surging at low speeds and during acceleration. This surging is in the longitudinal direction, felt about 2 cycles |
02-006-20-3688 | MAZDA | MAZDA3 | 2019 | Some vehicles may exhibit a rattle noise from the front suspension when driving over bumps or on a road with a wavy surface. The noise may be caused b |
16-001-20-3683a | MAZDA | MAZDA3 | 2019 | Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA01_11002 or later). M |
09-018-20-3690 | MAZDA | MAZDA3 | 2019 | Some customers may notice white lines appearing across the instrument cluster (as shown below). The white lines may be caused during the production pr |
09-017-20-3701 | MAZDA | MAZDA3 | 2019 | Some customers may experience that the door locks may not operate using the touch sensor on the outer door handle while parked in a parking space surr |
09-016-20-3693 | MAZDA | MAZDA3 | 2019 | Some customers may find that they cannot lock their vehicle when using the touch sensor (shown below) on the front door handle, however, they can unlo |
09-014-20-3700 | MAZDA | MAZDA3 | 2019 | Some customers may experience ÿ¿Ultrasonic sensor malfunctionÿ¿ÿ warning message displayed in the instrument cluster wh |
09-013-20-3663 | MAZDA | MAZDA3 | 2019 | When the Telematics Communication Unit (TCU) has been replaced or reprogrammed and the software is updated to ones shown below, DTC U2050:55-TCU (Acti |
07-002-20-3692a | MAZDA | MAZDA3 | 2019 | Some customers may notice that the temperature setting of the automatic climate control may not change when the temperature dial is operated very slow |
07-002-20-3692 | MAZDA | MAZDA3 | 2019 | Some customers may notice that the temperature setting of the automatic climate control may not change when the temperature dial is operated very slow |
01-010-20-3706 | MAZDA | MAZDA3 | 2019 | Some customers may experience a no start because the battery is discharged after the vehicle is parked for more than 8 hours. This may be caused by on |
CSP06d | MAZDA | MAZDA3 | 2019 | CSP06 - 2019 MAZDA3 MODULE UPDATE FOR CONNECTED SERVICES. Please review the newest repair procedure updated today, September 25, 2020 that performs 2 |
SA-029-20a | MAZDA | MAZDA3 | 2019 | Some customers may experience a "IN-VEHICLE NETWORK MALFUNCTION" warning message in the instrument cluster with one or more of the following DTC's st |
SA-027-20a | MAZDA | MAZDA3 | 2019 | MAZDA CONNECT Software Version 11002. NOTE: Mazda3 owners may notice an icon in their infotainments display that indicates Mazda Connected Serv |
SA-010-20a | MAZDA | MAZDA3 | 2019 | When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to initialize the new TCU after replacement. Use the infor |
SA-054-20b | MAZDA | MAZDA3 | 2019 | Some customers may experience an engine no start due to low battery voltage on 2019-2020 Mazda3 and 2020 CX-30. Inform the customer that Mazda is acti |
SA-029-20f | MAZDA | MAZDA3 | 2019 | Some customers may experience a "IN-VEHICLE NETWORK MALFUNCTION" warning message in the instrument cluster with one or more of the following DTC's sto |
SA-027-20c | MAZDA | MAZDA3 | 2019 | Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.<br /> |
SA-004-20b | MAZDA | MAZDA3 | 2019 | In order to ensure key code security, MNAO has restricted key code access for the new auxiliary key. This Service Alert provides information on how to |
MSP56 | MAZDA | MAZDA3 | 2019 | Effective immediately, MSP56 has been suspended until further notice. MSP56 was launched to prevent 2019 Mazda3 5dr vehicles from locking, if the keys |
SA-019-19 | MAZDA | MAZDA3 | 2019 | Some vehicles may experience M-MDS (MDARS) showing the front radar dynamic aiming is incomplete, although the procedure is completed. This is caused b |
07-006-19-3629b | MAZDA | MAZDA3 | 2019 | Some customers may experience that after starting the engine, the auto A/C blows warm air for about 10 minutes and then blows cool air as desired. Thi |
SA-039-19b | MAZDA | MAZDA3 | 2019 | During BCM replacement, MDARS may display a Configuration Error warning message. This may be caused by any of the following: ï¿· Po |
SA-042-19a | MAZDA | MAZDA3 | 2019 | Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.<br /> |
15-003-3597a | MAZDA | MAZDA3 | 2019 | Some vehicles may exhibit DTC B14F0:76 [VCM] (Forward sensing camera (FSC) deviation) stored in memory and the i-ACTIVSENSE warning light (amber) on a |
09-037-19-3636 | MAZDA | MAZDA3 | 2019 | Some customers may experience one or both of the following: The â¿¿Next Service Dateâ¿ setting under Vehicle Status |
SA-059-19 | MAZDA | MAZDA3 | 2019 | Some customers may complain that the seat warmer turns off after 10 minutes in manual mode and will not turn back on until the vehicle is restarted. D |
SA-055-19 | MAZDA | MAZDA3 | 2019 | Some vehicles may store DTC U2050:55 (Activation of remote control not implemented) after a BCM software update. Follow the repair procedure when this |
SA-018-20 | MAZDA | MAZDA3 | 2019 | Some customers may complain about any of the following:Warning light, Warning message, Headlight(s) inoperative, Cannot shift out of Park, Many DTC's |
SA-017-20 | MAZDA | MAZDA3 | 2019 | BODY CONTROL MODULE (BCM), VEHICLE CONTROL MODULE (VCM) OR INSTRUMENT CLUSTER (IC) MDARS SOFTWARE UPDATE FAILURE<br /> |
SA-014-20 | MAZDA | MAZDA3 | 2019 | On some vehicles, the Commander switch might be inoperative. This could be caused by fuse F13 (15A) being removed instead of F15 (15A) at the factory |
SA-012-20a | MAZDA | MAZDA3 | 2019 | 2019-2020 MAZDA3 SERVICE CAUTIONS FOR NEW AND REVISED FEATURES. The 2019-2020 Mazda3 has new and revised features that are different from previous mod |
SA-012-20 | MAZDA | MAZDA3 | 2019 | 2019-2020 MAZDA3 SERVICE CAUTIONS FOR NEW AND REVISED FEATURES. The 2019-2020 Mazda3 has new and revised features that are different from previous mod |
09-009-20-3665 | MAZDA | MAZDA3 | 2019 | Some customers may notice that the rear turn lights only flash once instead of twice for the answer-back when a door unlock operation is performed us |
01-018-19-3642 | MAZDA | MAZDA3 | 2019 | Some vehicles that have a drained battery recovered may exhibit that the engine will not start and the ignition switch will not turn off. The followin |
07-001-20-3660 | MAZDA | MAZDA3 | 2019 | Some customers may experience one side (driver side or passenger side) blowing warmer air out of the vents with the same or very close temperature set |
SA-003-20c | MAZDA | MAZDA3 | 2019 | When the body control module (BCM) has been replaced or reprogrammed and the software is updated to the file names shown below, DTC U2050:55-BCM (Acti |
09-010-20-3656 | MAZDA | MAZDA3 | 2019 | Some customers may notice a rattle noise from the instrument panel while driving that is localized at the active driving display. The noise is generat |
15-001-20-3652 | MAZDA | MAZDA3 | 2019 | Some customers may complain about a shift shock and/or an engine RPM increase when setting the Mazda Radar Cruise Control (MRCC) system with no DTCs b |
SA-010-20 | MAZDA | MAZDA3 | 2019 | TELEMATICS COMMUNICATION UNIT (TCU) INITIALIZATION PROCEDURE: When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MD |
SA-008-20 | MAZDA | MAZDA3 | 2019 | INSTRUMENT CLUSTER WARNING MESSAGE "SAFETY AND DRIVER SUPPORT SYSTEMS PARTIALLY DISABLED" AND DTC U0401:68 IS STORED:Some customers may experience an |
SA-006-20 | MAZDA | MAZDA3 | 2019 | WARNING MESSAGE SAFETY AND DRIVER SUPPORT SYSTEMS PARTIALLY DISABLED WITH DTC U2511:68: Some customer's may compain about warning message "Safety And |
SA-004-20 | MAZDA | MAZDA3 | 2019 | AUXILIARY KEY CUTTING TEMPORARY PROCEDURE: Currently, Mazda does not have a way to cut the auxiliary keys for the new style remote transmitter as they |
SA-003-20 | MAZDA | MAZDA3 | 2019 | DTC U2050:55 STORED AFTER REPLACING OR REPROGRAMMING BCM:When the body control module (BCM) has been replaced or reprogrammed and the software is upda |
SA-002-20 | MAZDA | MAZDA3 | 2019 | WIRELESS CHARGING PAD INSTALLATION INSTRUCTIONS CORRECTION: Section 6 of the Wireless Charging Pad instructions call for the use of an "ultrasonic cut |
SA-001-20 | MAZDA | MAZDA3 | 2019 | When performing Recall 4219L, make sure to connect a battery charger as stated in the Recall. If there are any issues, contact Hotline for assistance. |
MSP56a | MAZDA | MAZDA3 | 2019 | MSP56 - MODULE REPROGRAMMING TO PREVENT KEYS FROM BEING LOCKED INSIDE VEHICLE<br /> |
16-001-20-3683 | MAZDA | MAZDA3 | 2019 | AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (7TH GENERATION MODELS):Some vehicles may experience the symptoms mentione |
MSP27 | MAZDA | MAZDA3 | 2019 | Mazda Motor Corporation has decided to conduct a Mazda Service Program (MSP) on certain 2019 Mazda3 5HB vehicles produced from November 6, 2018 throug |
SA-046-19 | MAZDA | MAZDA3 | 2019 | On the 2019 Mazda3 (BP) and and all 2020 Mazda vehicles (except CX-3), the CR2032 button cell battery is required for the new type remote transmitter. |
07-006-19-3629a | MAZDA | MAZDA3 | 2019 | Some customers may experience that after starting the engine, the auto A/C blows warm air for about 10 minutes and then blows cool air as desired. Thi |
SA-042-20 | MAZDA | MAZDA3 | 2019 | Some customer may experience all of the following when turning the ignition ON under hot weather conditions such as parking under the hot sun for some |
SA-040-20 | MAZDA | MAZDA3 | 2019 | Key Transmitter Power Saving Function: When the key transmitter Power Saving Function is turned ON, transmitter battery power consumption is restricte |
01-004-20-3684 | MAZDA | MAZDA3 | 2019 | Some customers may experience the master warning light turning on and a lack of power with DTC P2BF6:00 (Exhaust shutter valve position sensor circuit |
SA-012-20c | MAZDA | MAZDA3 | 2019 | 2019-2020 MAZDA3 SERVICE CAUTIONS FOR NEW AND REVISED FEATURES. The 2019-2020 Mazda3 has new and revised features that are different from previous mod |
SA-003-20b | MAZDA | MAZDA3 | 2019 | When the body control module (BCM) has been replaced or reprogrammed and the software is updated to the file names shown below, DTC U2050:55-BCM (Acti |
SA-034-20 | MAZDA | MAZDA3 | 2019 | DTC P0942:49 TROUBLESHOOTING: P0942:49 is missing from the Workshop Manual on MGSS. Follow the repair procedure below to repair the vehicle until the |
SA-033-20 | MAZDA | MAZDA3 | 2019 | Some customers may complain about SiriusXM Travel Link, Traffic Plus showing expired even though the customer purchased a paid subscription. SiriusXM |
SA-032-19 | MAZDA | MAZDA3 | 2019 | When replacing the Body Control Module (BCM) in a 2019 Mazda3, it needs to be configured and the instructions in the Workshop manual on MGSS are incor |
SA-029-20 | MAZDA | MAZDA3 | 2019 | Some customers may experience a "IN-VEHICLE NETWORK MALFUNCTION" warning message in the instrument cluster with one or more of the following DTC's sto |
SA-028-20 | MAZDA | MAZDA3 | 2019 | Refer to the Repair Procedure when installing the trunk weatherstrip for guidance, otherwise water may enter the trunk during heavy rain or when going |
SA-027-20 | MAZDA | MAZDA3 | 2019 | Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE NOTE: Before proceed |
SA-021-20 | MAZDA | MAZDA3 | 2019 | The Mexico built Mazda3 trunk has been disabled (interior and exterior switches do not work) during shipment from Mexico to help prevent theft of the |
SA-012-20b | MAZDA | MAZDA3 | 2019 | 2019-2020 MAZDA3 SERVICE CAUTIONS FOR NEW AND REVISED FEATURES. The 2019-2020 Mazda3 has new and revised features that are different from previous mod |
SA-003-20a | MAZDA | MAZDA3 | 2019 | When the body control module (BCM) has been replaced or reprogrammed and the software is updated to the file names shown below, DTC U2050:55-BCM (Acti |
01-021-19-3649 | MAZDA | MAZDA3 | 2019 | Some customers may experience the CHECK ENGINE light ON with DTC P0012:00 (Electric variable valve timing control system: Over-retarded) stored in PCM |
09-036-19-3623a | MAZDA | MAZDA3 | 2019 | Some customers may complain about an instrument cluster warning message "Auto Light System Malfunction. Turn On/Off Lights Manually". DTC B10AD:09 (Hu |
01-020-19-3641 | MAZDA | MAZDA3 | 2019 | |
SA-050-19 | MAZDA | MAZDA3 | 2019 | FSC dynamic aiming (mid-drive aiming) may not complete if the vehicle is driven on a road as described below: ï¿· The road lane mar |
SA-039-19a | MAZDA | MAZDA3 | 2019 | During BCM replacement, MDARS may display a Configuration Error warning message. This may be caused by any of the following: ï¿· Po |
09-027-19-3615 | MAZDA | MAZDA3 | 2019 | Some customers may experience that the MAZDA CONNECT unexpectedly announces navigation guidance when the Connectivity Master Unit (CMU) wakes up even |
SA-032-19 | MAZDA | MAZDA3 | 2019 | When replacing the Body Control Module (BCM) in a 2019 Mazda3, it needs to be configured and the instructions in the Workshop manual on MGSS are incor |
SA-019-19 | MAZDA | MAZDA3 | 2019 | Some vehicles may experience M-MDS (MDARS) showing the front radar dynamic aiming is incomplete although the procedure is completed. This is caused by |
08-002-19-3600 | MAZDA | MAZDA3 | 2019 | Some vehicles with the two-step deployment control air bag module may exhibit a clicking sound when turning the steering wheel. This is caused by the |
SA-039-19 | MAZDA | MAZDA3 | 2019 | During BCM replacement, MDARS may display a Configuration Error warning message. This may be caused by any of the following: Poor internet connection, |
SA-038-19 | MAZDA | MAZDA3 | 2019 | There is currently a known issue with the latest MDARS update and Mazda is working to resolve the issue. The concern is due to added functionality for |
SA-037-19 | MAZDA | MAZDA3 | 2019 | Key Transmitter Power Saving Function: When the key transmitter Power Saving Function is turned ON, transmitter battery power consumption is restricte |
SSPB6 | MAZDA | MAZDA3 | 2019 | 2014-2016 Mazda3 â¿¿ Mazda Connect Touch Screen Concern. Warranty Extension Program â¿¿ Special Service Progra |
SA-010-19b | MAZDA | MAZDA3 | 2019 | 2019 MAZDA3 SERVICE CAUTIONS FOR NEW AND REVISED FEATURES: The new 2019 Mazda3 has new features that may be difficult to understand. This Service Aler |
09-035-19-3637 | MAZDA | MAZDA3 | 2019 | If the body control module (BCM) or the LF control unit (LFU) has been replaced and configuration has been performed, communication between the BCM an |
SA-014-19a | MAZDA | MAZDA3 | 2019 | Some customers may experience a warning message in the instrument cluster that says "IN-VEHICLE NETWORK MALFUNCTION" with no DTC's stored.<br /> |
07-006-19-3629 | MAZDA | MAZDA3 | 2019 | Some customers may experience that after starting the engine, the auto A/C blows warm air for about 10 minutes and then blows cool air as desired. Thi |
SA-028-19 | MAZDA | MAZDA3 | 2019 | Some customers may complain about a shift shock at 40-60 mph and/or an engine RPM increase when setting the MRCC with no DTCs are stored. This may be |
SA-017-19b | MAZDA | MAZDA3 | 2019 | The 2019 Mexico built Mazda3 trunk has been disabled (interior and exterior switches do not work) during shipment from Mexico to help prevent theft of |
SA-010-19g | MAZDA | MAZDA3 | 2019 | 2019 MAZDA3 SERVICE CAUTIONS FOR NEW AND REVISED FEATURES. The new 2019 Mazda3 has new and revised features that are different from previous models, a |
SA-010-19f | MAZDA | MAZDA3 | 2019 | 2019 MAZDA3 SERVICE CAUTIONS FOR NEW AND REVISED FEATURES. The new 2019 Mazda3 has new and revised features that are different from previous models, a |
Subscribe for our latest newslatters
Know if there is a safety problem with your vehicles, tires or car seat, and how to get it fixed.