| Bulletin Number | Vehicle Make | Vehicle Model | Model Year | Summary |
|---|---|---|---|---|
| IS-14136 CO-21re | PREVOST | X3 | 2019 | This Instruction Sheet explains how to add 2 aluminium sun visors to the front winsdhield<br /> |
| MI21-01 | PREVOST | X3 | 2015 | VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING<br /> |
| IS-18091A | PREVOST | X3 | 2019 | TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles. The new |
| IS-20913A | PREVOST | X3 | 2020 | POWER STEERING 20 ft STAINLESS STEEL PIPE REPAIR PROCEDURE - Addition of ORS plug in Other Material<br /> |
| IS-19912A | PREVOST | X3 | 2017 | ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR - Mention added stating to disable ⿿Prime; Parts added in the kit.<br / |
| IS-19901A | PREVOST | X3 | 2017 | ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR - X3 SERIES US10 UP TO GHG17 COOLING SYSTEM - Mention added stating to disable ⿿P |
| MI20-08B | PREVOST | X3 | 2020 | STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020<br /> |
| MI20-12 | PREVOST | X3 | 2014 | JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models ⿿ equipped with RB Bosch/ZF Servocom or Servocomtronic s |
| IS-19923A | PREVOST | X3 | 2007 | Revision : Addition of Wiring Schematics at the end of this document<br /> |
| IS-19901 | PREVOST | X3 | 2017 | This Instruction sheet explains how to install the Electric Cooling System with Bosch Alternators on X3 series vehicles equipped with US10 up to GHG1 |
| SCI19-01C | PREVOST | X3 | 2018 | The intent of this procedure is to guide you through the steps required to program a MCM especially for the control of the electric fan drive as requi |
| IS-19901 | PREVOST | X3 | 2017 | This Instruction sheet explains how to install the Electric Cooling System with Bosch Alternators on X3 series vehicles equipped with US10 up to GHG17 |
| IS-18158 | PREVOST | X3 | 2019 | TOILET DRAIN VALVE REPLACEMENT<br /> |
| MI19-32 | PREVOST | X3 | 2007 | This Maintenance Information explains how to install harness #7770134, designed to bypass the Engine Compartment Harness (Prevost part), connecting th |
| SP19-301 | PREVOST | X3 | 2016 | On the vehicles affected by this bulletin, the compressor & radiator door lower hinges must be replaced by new stainless steel units<br /> |
| IS-19922 | PREVOST | X3 | 2016 | PREVOST AWARE ADAPTIVE CRUISE BRAKING (ACB) FLR10 TO FLR21 RADAR SENSOR UPGRADE<br /> |
| IS-19915 | PREVOST | X3 | 2019 | MP-1000 MULTIMEDIA PLAYER INSTALLATION<br /> |
| IS-17906A | PREVOST | X3 | 2008 | This instruction sheet explains how to install an ELD interface kit for Prevost Vehicles equipped with Multiplex Detroit Diesel Engines<br /> |
| IS-17071A | PREVOST | X3 | 2018 | This instruction sheet explains how to install an ELD interface on OBD vehicles<br /> |
| SP18-35B_English | PREVOST | X3 | 2019 | On vehicles with active code P20EE, perform the following checklist and operations.<br /> |
| sp19-26A | PREVOST | X3 | 2019 | On the vehicles affected by this bulletin, an update to the engine EMS software must be carried out by qualified technicians. Contact your Service Man |
| IS-18907 | PREVOST | X3 | 2017 | This instruction sheet explains how to install hatches with fan on X3 vehicles.<br /> |
| SP18-307 | PREVOST | X3 | 2016 | On the vehicles affected by this bulletin, the Bitzer compressor shaft seal must be replaced. Additionally, the compressor oil must be renewed and the |
| MI19-06 | PREVOST | X3 | 2019 | This Maintenance Information is published to answer some questions regarding the inverted or ?trailing? mounting position of the drive axle brake cali |
| MI19-05 | PREVOST | X3 | 2019 | This Maintenance Information expains how to adjust p/n 660865, 660699 draglinks<br /> |
| IS-17102A | PREVOST | X3 | 2018 | This Instruction sheet explains how to install ISM (Intelligent Sleep Mode) On X Series With Prime Hardware<br /> |
| SP18-13F | PREVOST | X3 | 2008 | On the vehicles affected by this bulletin, proceed to the replacement of the drag link.<br /> |
| IS-19909 | PREVOST | X3 | 2017 | This instruction sheet explains how to perform alternator conversion, from Bosch to Delco Remy, on X3 vehicles<br /> |
| IS-19906 | PREVOST | X3 | 2019 | This instruction sheet explains how to perform alternator conversion, from Bosch to Delco Remy, on X3 vehicles equipped with EFD<br /> |
| IS-18909 | PREVOST | X3 | 2010 | This instruction sheet explains how to replace the Carrier AC compressor with a Bitzer<br /> |
| SP19-09 | PREVOST | X3 | 2019 | On the vehicles affected by this bulletin, add a jumper on connector A175.<br /> |
| SCI18-46 | PREVOST | X3 | 2019 | This Service Center Instructions explains how to install the Prevost Ultimate Entertainment System<br /> |
| SP19-09B | PREVOST | X3 | 2019 | On the vehicles affected by this bulletin, add a jumper on connector A175.<br /> |
| MI18-05 | PREVOST | X3 | 2017 | This maintenance information explains how to install valve assembly 130009 in replacement of valve 641274<br /> |
| WB18-01A | PREVOST | X3 | 2018 | On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding |
| WB16-02H | PREVOST | X3 | 2016 | On the vehicles affected by this bulletin, it is necessary to perform a Multiplex software update plus other corrective measures to improve the chargi |
| SP17-314-R13 | PREVOST | X3 | 2016 | This bulletin explains how to install a light at the entrance door.<br /> |
| WB18-07B | PREVOST | X3 | 2018 | On the vehicles affected by this bulletin, the busbar connected to circuit breaker CB13 (power inverter) may have been installed reversely. It is nece |
| Sp18-304A | PREVOST | X3 | 2016 | For vehicles affected by this bulletin, on the wheelchair area sliding door, install a new upper roller carrier, adjust the door and inspect all faste |
| Sp18-303 | PREVOST | X3 | 2016 | On the vehicles affected by this bulletin, the condenser compartment wall may present fatigue cracks on or near the A/C receiver tank support. Follow |
| Sp18-301 | PREVOST | X3 | 2016 | On the vehicles affected by this bulletin, the existing surge tank support has to be replaced by a new configuration including two supports. That will |
| Sp18-20 | PREVOST | X3 | 2018 | On the vehicles affected by this bulletin, replace the AC compressor discharge hose.<br /> |
| MI18-27 | PREVOST | X3 | 2018 | This maintenance information presents the Amerex fire suppression system, and its recommended maintenance<br /> |
| MI18-18 | PREVOST | X3 | 2018 | This maintenance information explains how to tow and hoist Prevost vehicles.<br /> |
| MI16-08B | PREVOST | X3 | 2011 | This Maintenance Information presentes the new method of locking the electromagnetic clutch in the event of a failure. These new electromagnetic clut |
| IS-18901 | PREVOST | X3 | 2018 | This instruction sheet explains how to install the engine belt guard on X3 Series vehicles with coolant system electrical fan drive.<br /> |
| Sp18-302 | PREVOST | X3 | 2016 | On the vehicles affected by this bulletin, install a pressure switch into the front service compartment to send a faster signal to the Allison transmi |
| MI18-22 | PREVOST | X3 | 2018 | This Maintenance Information presents information about the ELD Installation and Parameter List on Prevost Coaches<br /> |
| MI18-21 | PREVOST | X3 | 2018 | This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/ |
| MI18-16A | PREVOST | X3 | 2018 | This Maintenance Information presents guidelines to help with the diagnosis of the Bosch HD10 alternators<br /> |
| SP18-308A | PREVOST | X3 | 2018 | On the vehicles affected by this bulletin, add 300ml of oil in the Bitzer A/C compressor as per production retrofit R18053.<br /> |
| SP18-306 | PREVOST | X3 | 2018 | On the vehicles affected by this bulletin, update EMS and ACM software to the latest version available.<br /> |
| MI18-37 | PREVOST | X3 | 2018 | This Maintenance Information presents information about the removal or installation of the Lang KK73.1 electromagnetic clutch - part of the Bitzer (m |
| MI18-27A | PREVOST | X3 | 2018 | This maintenance information presents the Amerex fire suppression system, and its recommended maintenance<br /> |
| MI18-21A | PREVOST | X3 | 2018 | This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/ |
| IS-18904 | PREVOST | X3 | 2018 | This procedure shows how to install a rear camera.<br /> |
| MI18-27B | PREVOST | X3 | 2018 | This maintenance information presents the Amerex fire suppression system, and its recommended maintenance<br /> |
| SP18-305A | PREVOST | X3 | 2015 | On the vehicles affected by this bulletin, apply thread locker on the double door latch pins internal threads<br /> |
| WB18-03 | PREVOST | X3 | 2018 | On the vehicles affected by this bulletin, due to a software issue, replace the battery equalizer in the main power compartment.<br /> |
| wb17-16 | PREVOST | X3 | 2014 | On the vehicles affected by this bulletin, remove selected wires from C15 and C58 of the HVAC system wiring, and place them in new connectors C15B and |
| IS-18901 | PREVOST | X3 | 2018 | This instruction sheet explains how to install an engine belt guard<br /> |
| IS-17906 | PREVOST | X3 | 2008 | This instruction sheet explains how to install an ELD interface kit for Prevost Vehicles equipped with Multiplex Detroit Diesel Engines<br /> |
| IS-18902 | PREVOST | X3 | 2018 | This instruction sheet explains how to installa parcel rack door kits<br /> |
| WB18-09 | PREVOST | X3 | 2018 | On the vehicles affected by this bulletin, one of the battery ground cables may have been incorrectly crimped and must be replaced following the proce |
| WB18-08 | PREVOST | X3 | 2018 | On the vehicles affected by this bulletin use the following procedure to install the engine belt guard.<br /> |
| WB18-07 | PREVOST | X3 | 2018 | On the vehicles affected by this bulletin, the busbar connected to circuit breaker CB13 (power inverter) may have been installed reversely. It is nece |
| SP18-13D | PREVOST | X3 | 2008 | On the vehicles affected by this bulletin, proceed to the replacement of the drag link.<br /> |
| WB18-06 | PREVOST | X3 | 2018 | On the vehicles affected by this bulletin, replace the existing right console ramp p/n 392494 with the new right console ramp p/n 3200962.<br /> |
| WB18-07A | PREVOST | X3 | 2018 | On the vehicles affected by this bulletin, the busbar connected to circuit breaker CB13 (power inverter) may have been installed reversely. It is nece |
| SP18-13E | PREVOST | X3 | 2008 | On the vehicles affected by this bulletin, replace the drag link.<br /> |
| SP17-314 | PREVOST | X3 | 2016 | This bulletin explains how to install a light at the entrance door.<br /> |
| MI18-02 | PREVOST | X3 | 2018 | This Mainteannce Informaiton presents the latest engine oil & filter change intervals for the Volvo Engine<br /> |
| IS-17905 | PREVOST | X3 | 2018 | This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines<br /> |
| IS-13009B | PREVOST | X3 | 2018 | This instruction sheet explains how to install and adjust drag link # 660699<br /> |
| IS-17907 | PREVOST | X3 | 2018 | This instruction sheet explains how to install the Volvo Electronic Logging Device (ELD)<br /> |
| SP17-314 | PREVOST | X3 | 2016 | On the vehicles affected by this bulletin, install a light at the entrance door.<br /> |
| SP17-313 | PREVOST | X3 | 2016 | On the vehicles affected by this bulletin, replace the batteries by a new set (4) of the same model; perform several verifications on the alternator a |
| IS-17071 | PREVOST | X3 | 2018 | This instruction sheet explains how to install an ELD interface on OBD vehicles<br /> |
| WB14-03 | PREVOST | X3 | 2013 | On the vehicles affected by this bulletin, a new center mount battery box cover offering better overall sealing and simplified installation is availab |
| SP14-21G | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, replace and relocate the LTD. Remove the existing IR sensor and install an updated IR sensor. Finally, remo |
| SP14-306D | PREVOST | X3 | 2014 | On the vehicles affected by this bulletin, replace the engine harness as described in the following procedure.<br /> |
| SP14-303A | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, to cancel the DID pop-up message ?windows ajar? disconnect wire 260 from MUX module A42.<br /> |
| MI1423 | PREVOST | X3 | 2008 | A new software version (v1.06) is available to update the CANtrak (Tire Pressure Monitoring System) module. This new version will allows a 10 min. de |
| SP14-307A | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, install a warning plate.<br /> |
| SP14-302C | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, perform an improvement of the front windshield sun visor guides and supports in addition to the side window |
| SP14-304 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, replace the sliding door interior post finishing trims as described in the following procedure.<br /> |
| SP14-305A | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, replace the bi-fold door hinge arm rod ends as described in the following procedure<br /> |
| WB14-27 | PREVOST | X3 | 2014 | On the vehicles affected by this bulletin, interference may occur between a cable bundle and part of the drive axle surrounding structure when suspens |
| SP13-52 | PREVOST | X3 | 2014 | Risk of premature failure of top fan support due to absence of weld. In the engine compartment above radiator, inspect support to make sure support ha |
| IS-08080 | PREVOST | X3 | 2008 | When replacing a vehicle sound selector model VSS04 with a new sound selector model VSS05, an interface harness is required to connect the vehicle har |
| SP13-43 | PREVOST | X3 | 2013 | Interference may occur between the WCL platform and the cassette access door when the platform is loaded at its extremity while lifting.<br /> |
| SP13-42 | PREVOST | X3 | 2013 | Inspect each gas cylinder to make sure there is no interference with the passenger's floor stiffeners when luggage door is closed.<br /> |
| SP13-323 | PREVOST | X3 | 2013 | ON the vehicles affected by this bulletin, update the Engine air intake pipe.<br /> |
| SP13-322 | PREVOST | X3 | 2008 | On the vehicles affected by this bulletin, relocate the video fuse in the SMI box closer to the door for better access.<br /> |
| SP13-321 | PREVOST | X3 | 2008 | On the vehicles affected by this bulletin, at next service occasion, open the C69 connector located in the front compartment and check for presence of |
| SP13-320 | PREVOST | X3 | 2008 | On the vehicles affected by this bulletin, if needed, the celling panel needs to be removed and material glued again.<br /> |
| SP13-319 | PREVOST | X3 | 2011 | On the vehicles affected by this bulletin, follow the enclosed procedure to correct surface corrosion on seat pedestals.<br /> |
| SP13-318 | PREVOST | X3 | 2008 | On the vehicles affected by this bulletin, take the following measure to improve dust handling. Seal the evaporator compartment to prevent dust entry, |
| SP13-317 | PREVOST | X3 | 2013 | On the vehicles affected by this bulletin, clean the breakers posts and bus bars, apply corrosion protection. Check compartment cover seal condition.< |
| SP13-314 | PREVOST | X3 | 2008 | On the vehicles affected by this bulletin, follow the enclosed procedure to remove corrosion around luggage doors.<br /> |
| SP13-324 | PREVOST | X3 | 2013 | On the vehicles affected by this bulletin, an improved 90 degree elbow is available. Proceed to replacement at next service occasion.<br /> |
| SP13-315 | PREVOST | X3 | 2013 | On the vehicles affected by this bulletin, replace the destination sign power harness to resolve electrical interference between sign and public addre |
| SP13-38 | PREVOST | X3 | 2013 | Rear fender support arm & WCL door spring replacement.<br /> |
| SP13-313 | PREVOST | X3 | 2009 | For condenser that have been replaced by customer already. We still need to cut floor and shroud for drainage.<br /> |
| SP13-34A | PREVOST | X3 | 2014 | On the vehicles affected by this bulletin, a relay needs to be added to allow the DEF to return to the tank after turning the key to the OFF position. |
| SP13-30 | PREVOST | X3 | 2011 | On the vehicles affected by this bulletin, a contact possibility exists between the power supply cable and the support sharp edge of the 24VDC/120VAC/ |
| SP13-22 | PREVOST | X3 | 2014 | Radius rod support weld inspection: weld beads may be too small on radius rod supports on rear sub-frame.<br /> |
| SP13-312 | PREVOST | X3 | 2012 | Replace the 4 Stressproof steel door studs with the new Hex door studs<br /> |
| SP13-23 | PREVOST | X3 | 2013 | On the vehicles affected by this bulletin, there is a risk of bi-metal contact (stainless steel & aluminum) leading to corrosion where side refle |
| SP13-311 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, multiple codes for PSID8 FMI2 or 1 after reprogramming engine, agreed to campaign Piston cooling reduction |
| SP13-21 | PREVOST | X3 | 2013 | Following introduction of new aluminium doors on x serie vehicles equipped with WCL, the decal showing how to manualy operate the wcl (on the wcl acc |
| SP13-310 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, force UIP regen and replace doser modules as requested<br /> |
| SP13-18 | PREVOST | X3 | 2013 | Possibility of galvanic corrosion between the aluminium door and the stainless steel evaporator door retaining mechanism. Procedure to solve the issu |
| WB13-02 | PREVOST | X3 | 2011 | On the vehicles affected by this bulletin, the lavatory mirror may break around the key latch when applying pressure. Replace by an improved lavatory |
| SP13-309 | PREVOST | X3 | 2012 | Multiple hose failures, agreed with customer to replace Silicone hose in engine compartment for coaches with Volvo engine.<br /> |
| SP13-307 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, replace R6 and R13 Relay Indirect and direct lightening, as premature failure of R6 and R13 due to the rela |
| SP13-305 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, replace coolant hose for the most recent hose.<br /> |
| SP13-302 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, trim WCL seat pedestal block to make them easier to slide back and forward and reduce pedestal failures.<br |
| SP13-303 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, reprogram engine to improve Piston cooling codes<br /> |
| SP13-304 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, look at all the clamps and retighten as coolant leaks found around the coach.<br /> |
| SP13-300 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, change one parameter in the cluster software to fix the PID251 clock code.<br /> |
| SP13-301 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, replace booster pump support as vehicles with cracked support found during inspection.<br /> |
| SP12-313 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, reinforced parking brake overrule tank supports are available.<br /> |
| SP12-319 | PREVOST | X3 | 2009 | On the vehicles affected by this bulletin, proceed to proactive replacement of Aluminum Condenser to Copper condenser<br /> |
| SP12-320 | PREVOST | X3 | 2009 | Proactiverly replace Lining fan clutch with KM fan cluch and shaft<br /> |
| SP12-321 | PREVOST | X3 | 2009 | On the vehicles affected by this bulletin, proactively replace the fan clutch support while replacing the fan clutch, Improvement will be made to th |
| SP12-306A | PREVOST | X3 | 2013 | On the vehicles affected by this bulletin, improvement of a Charge Air Cooler tube support is required. This is a ?Fix as Fail? bulletin, repair only |
| WB12-33 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, the wheelchair lift sliding door hinge bolts need to be tightened to ensure proper torque is applied. Proce |
| SP12-312 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, addition of a power relay to the inverter system wiring is required.<br /> |
| SP12-318 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, install washers on front passengers modesty panel to increase gap between hand rail and panel<br /> |
| SP12-316 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, the Bi?Part Door Studs must be replaced with latest version .<br /> |
| SP12-317 | PREVOST | X3 | 2013 | On the vehicles affected by this bulletin, install a rock shield under Crank shaft to prevent belts from being thrown<br /> |
| SP12-314 | PREVOST | X3 | 2012 | Replace edge moulding retainer clip to improve the reliability of this installation<br /> |
| IS12047 | PREVOST | X3 | 2013 | This instruction sheet explains how to install additional restraint for plastic shields over drive axle wheels. Use kit #3200407 to secure the shield |
| SP12-311 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, relocation of the wcl pendant is required to avoid driver to pull on the wires when operating WCL<br /> |
| SP12-315 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, perform the replacement of the existing WCL sliding door upper arm.<br /> |
| SP12-307 | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, replace Drive axle radius rod bushings and caps to improve reliability.<br /> |
| SP14-309 | PREVOST | X3 | 2014 | On the vehicles affected by this special bulletin, replace the two visual brake wear indicators on the tag axle.<br /> |
| Wb18-01 | PREVOST | X3 | 2018 | On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding |
| Sp18-300 | PREVOST | X3 | 2016 | This bulletin explains how to replace ceiling transition pannels, when needed<br /> |
| SP16-304 | PREVOST | X3 | 2016 | On the vehicles affected by this bulletin, replace the battery connection decal by a new version.<br /> |
| MI16-07 | PREVOST | X3 | 2016 | Prevost is now offering a clutch replacement kit for vehicles equipped with a Kendrion (Linnig) LLW203 Series fan clutch and gearbox assembly. This k |
| SP16-301B | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, replace the turbocharger actuator (SRA).<br /> |
| IS-14154 | PREVOST | X3 | 2008 | This Instruction sheet explains how to modify the Support beam (Part # 30022 Installation)- as part of the X3 Fuel Tank installation<br /> |
| MI17-22 | PREVOST | X3 | 2018 | This Maintenance Information explains how to inspect the Fuel Tank Cradle Mounting Screws on a yearly basis<br /> |
| Sp16-323 | PREVOST | X3 | 2016 | On the vehicles affected by this bulletin, change a parameter in the MUX system to deactivate a DTC corresponding to air dryer cartridge change warnin |
| SP16-316D | PREVOST | X3 | 2012 | On the vehicles affected by this bulletin, the front fuel tank support needs to be improved to prevent fatigue cracks.<br /> |
| MI15-02 | PREVOST | X3 | 2008 | This Maintenance Information presents an improved differential breather kit, identical to the one now used in production. This new breather incorporat |
| SP16-19 | PREVOST | X3 | 2012 | On certain vehicles equipped with VOLVO D13 engines, the pinning of the double idler gear is necessary.<br /> |
| SP16-09 | PREVOST | X3 | 2013 | On the vehicles affected by this bulletin, inspect the fuel injectors serial numbers and replace if required.<br /> |
Subscribe for our latest newslatters
Know if there is a safety problem with your vehicles, tires or car seat, and how to get it fixed.