Manufacturer Communications
Vehicles / International
| Bulletin Number | Vehicle Make | Vehicle Model | Model Year | Summary |
|---|---|---|---|---|
| 20904 | INTERNATIONAL | MV | 2020 | Certain MV Series trucks built with Feature codes 14GVJ, 14GVX, or 14GVY (Axle rear tandem, Meritor MT 40 series) and with 14UNU (Suspension, rear air |
| 21501 | INTERNATIONAL | LT | 2021 | The battery ground cable may break at the frame connection resulting in loss of electrical power and unintended engine shut down without warning. Unin |
| IK0800593 | INTERNATIONAL | RH | 2021 | Radio clock changes time automatically; Only vehicles built after March 2020 and excluding CV<br /> |
| IK0400164 | INTERNATIONAL | CV | 2020 | Brake pedal pulsation while braking; Only CV series with feature code 0001ANB axle configuration (Navistar) 4 X 4<br /> |
| 20506 | INTERNATIONAL | LT | 2020 | Replacement of the Charge Air Cooler (CAC) outlet hose to prevent a potential increase of particulate matter emissions from a potential hose failure. |
| IK0500038 | INTERNATIONAL | RH | 2021 | Steering Shake, Shimmy, Shudder, Wobble, Steering Vibration; only models built with 14K weight rated axles or lower<br /> |
| IK0300074 | INTERNATIONAL | CV | 2020 | CV Air Spring Failure in Roll-back / Wrecker-hook applications<br /> |
| 20510 | INTERNATIONAL | HV | 2021 | On certain trucks equipped with an automatic transmission, if the automatic transmission is still in drive or reverse position and the stationary PTO |
| IK2600128 | INTERNATIONAL | RH | 2021 | A26, N13, and 2010 EPA MaxxForce 11 and 13 engine Auxiliary Programable Parameters<br /> |
| IK1400038 | INTERNATIONAL | HV | 2021 | Tridem Axle Oil Temperature Cluster Messages<br /> |
| IK0900141 | INTERNATIONAL | MV | 2021 | MV Air Compressor Inlet Hose Rubbing; only models with Cummins ISB engines and built 11/20/2019 through 11/06/2020<br /> |
| IK0100051 | INTERNATIONAL | 7000 | 2003 | Frame Rail Straightness Inspection Procedure<br /> |
| IK1201444 | INTERNATIONAL | LT | 2021 | 1 channel CPA RCT test for A26 or CV 6.6L; Only trucks built with International A26 or 6.6 engines<br /> |
| IK0800590 | INTERNATIONAL | LT | 2021 | Programming Procedure for Center Panel Switch Packs<br /> |
| 20905 | INTERNATIONAL | LONESTAR | 2020 | Recalibrate Transmission Control Unit (TCU) software to improve Linear Clutch Actuator (LCA) performance and mitigate possible transmission service la |
| IK0200013 | INTERNATIONAL | HX | 2021 | Suggested alignment target values when performing a vehicle axle alignment<br /> |
| IK0800590 | INTERNATIONAL | LT | 2021 | Programming Procedure for Center Panel Switch Packs<br /> |
| 21102 | INTERNATIONAL | LONESTAR | 2021 | The air filter elements may debond resulting in dirt entering the engine intake.<br /> |
| 21101 | INTERNATIONAL | LONESTAR | 2021 | The deaeration tank may leak coolant.<br /> |
| IK1600260 | INTERNATIONAL | LT | 2021 | Feature 16VLS Tire Pressure Maintenance System (TPMS)<br /> |
| IK1201453 | INTERNATIONAL | LT | 2021 | 7095496C3 EGR Bellows Heat Shield ID; only models equipped with A26 Engine<br /> |
| 20114 | INTERNATIONAL | HV | 2021 | Certain International® HV and MV Series trucks, and DuraStar and WorkStar model trucks, the battery ground circuit interconnect cable may have bee |
| IK1201454 | INTERNATIONAL | LT | 2021 | This document will guide the user through what is normal appearance for a NEU A26 replacement engine assembly. Only models built with International A2 |
| IK1500074 | INTERNATIONAL | LT | 2021 | Fuel Filters, Winter Additives, and Blending Fuels for Cummins® Engines<br /> |
| IK0800592 | INTERNATIONAL | CV | 2020 | This document will guide the user through a process to recover lost programmed values in engine ECM.<br /> |
| 20115 | INTERNATIONAL | LT | 2021 | Certain vehicles with a manual transmission may need the BCM to be updated for the over-the-air (OTA) programming to function.<br /> |
| IK0800590 | INTERNATIONAL | LT | 2021 | Programming procedures for the center panel switch packs has changed.<br /> |
| IK1300186 | INTERNATIONAL | HV | 2021 | Auxiliary Transmission Diagnostics; only models with feature code 0013607 or 0013PNB controlled by DLB feature 0597268<br /> |
| IK0800560 | INTERNATIONAL | LT | 2021 | Dielectric Grease Change<br /> |
| IK1600250 | INTERNATIONAL | HV | 2021 | Horizon Cab Door Field Replacement and the Side Window Air Deflectors. NOTE: This article will only be applicable to cabs with the deflector mounted o |
| IK0800504 | INTERNATIONAL | LT | 2021 | Repair Procedures for Vehicles Struck by Lightning<br /> |
| 20105 | INTERNATIONAL | LT | 2021 | The telematics module may not ⿿call home, resulting in an inability to perform over-the-air programming.<br /> |
| IK0700102 | INTERNATIONAL | LT | 2021 | DEF Coolant Line Leak Rear of Engine; only models with International A26 engine<br /> |
| IK1900022 | INTERNATIONAL | 8500 | 2008 | A/C Refrigerant and Oil Capacities<br /> |
| IK2600244 | INTERNATIONAL | CV | 2020 | |
| IK1700018 | INTERNATIONAL | CV | 2020 | Vehicles that experience an objectionable wheel end vibration felt in the cab at highway speeds.<br /> |
| IK1600233 | INTERNATIONAL | LT | 2021 | Cab Lean Concern<br /> |
| IK0400163 | INTERNATIONAL | LT | 2021 | Foot Valve Air Leak- Bendix ATR6 Traction Control Relay Valve Diagnostics; Only Models with Cummins X15 engine and feature code 04ECC air dryer<br /> |
| 20508 | INTERNATIONAL | HV | 2021 | Certain MV and HV series trucks do not conform to Federal Motor Vehicle Safety Standard (FMVSS) No. 108 relating to reflective tape missing on back of |
| 20507 | INTERNATIONAL | HX | 2021 | The bolts that attach the trailing arm to the steerable auxiliary lift axle may not be long enough to engage the locking feature of the corresponding |
| 20113 | INTERNATIONAL | HX | 2021 | For certain International HX Series trucks with Cummins® X15 engines, the bolts that attach the idler pully mounting bracket may not be long enoug |
| 20108 | INTERNATIONAL | LT | 2021 | The mirror glass of the hood mirrors may have been assembled incorrectly and could cause it to loosen from the housing.<br /> |
| 20106 | INTERNATIONAL | HV | 2021 | The upper fan ring shroud support bracket may have been assembled with an insufficient weld between the bracket and its mount which may cause the weld |
| 20505 | INTERNATIONAL | CV | 2020 | Certain International CV Series trucks may not comply with Federal Motor Vehicle Safety Standard (FMVSS) 105 S5.3.1.C or Canada Motor Vehicle Safety S |
| 20504 | INTERNATIONAL | RH | 2020 | The connecting rod bushing over time may develop cracks or lose chunks of material which could lead to connecting rod engine failure. Connecting rod f |
| 20502 | INTERNATIONAL | CV | 2020 | This Emissions Recall applies to truck models that were built with 2019 and 2020 International 6.6 diesel engines; to improve Selective Catalytic Redu |
| IK1600259 | INTERNATIONAL | HV | 2021 | Chrome Plated C-Loop Mirror Flat Glass Cracks<br /> |
| IK1201448 | INTERNATIONAL | INTERNATIONAL | 9999 | A26 New Exchange Unit program has been developed by using a new short block assembly built from Huntsville Engine Plant.<br /> |
| IK1201442 | INTERNATIONAL | WORKSTAR | 2015 | 5 gallon SSI DEF level sensor/ multifunction head unit retrofit; only 2014 and 2015 models year built with Navistar N9/N10 engines<br /> |
| IK1201042 | INTERNATIONAL | INTERNATIONAL | 9999 | Air Gap Specs. for Crankshaft and Camshaft Position Sensors; only models equipped with 2004-2017 DT, 9, 10, N9, N10 Engines<br /> |
| IK1900261 | INTERNATIONAL | LT | 2021 | Bluetooth Cannot Be Connected to Radio<br /> |
| 20107 | INTERNATIONAL | HX | 2020 | The Air conditioning (A/C) refrigerant system may be overcharged resulting in excessive cooling fan operation and reduced fuel economy.<br /> |
| IK1201198 | INTERNATIONAL | 9900 | 2012 | MaxxForce 15L Engine Oil Leaks; an aid in repairing engine oil leaks on the MaxxForce 15L engine.<br /> |
| IK0800590 | INTERNATIONAL | LT | 2021 | Programming Procedure for Center Panel Switch Packs<br /> |
| IK0800284 | INTERNATIONAL | TRANSTAR | 2017 | Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics<br /> |
| IK4300009 | INTERNATIONAL | LT | 2021 | This document will guide the user through the proper use of the A26 Misfire Detection Session to determine cylinder misfire count releted to the speci |
| IK1600186 | INTERNATIONAL | TRANSTAR | 2013 | Cab Odor Service Plan Information; only models equipped with EPA 2010 or later MaxxForce 11 or MaxxForce 13 engines<br /> |
| 20503 | INTERNATIONAL | HV | 2019 | The steer axle hubs may not have lubricant filled to the proper level at time of assembly which may result in wheel bearing damage and in extreme inst |
| 20104 | INTERNATIONAL | LT | 2021 | Eaton AMT Calibration Update with 2020 Cummins® X15 Engines; only trucks built 02 January 2020 through 02 April 2020.<br /> |
| IK0800475 | INTERNATIONAL | HV | 2021 | Radio Diagnostics and Information<br /> |
| IK0900140 | INTERNATIONAL | HX | 2020 | HX Frequent Engine Fan Cycling with A/C; only models equipped with Integrated Receiver Drier Built Before 1/13/2020.<br /> |
| IK0800588 | INTERNATIONAL | INTERNATIONAL | 9999 | Guide the user through identifying and properly rerouting and clipping the wire harness for the fuel pressure control valve (EFA2 or FVCV). Only model |
| 20902 | INTERNATIONAL | CV | 2020 | The transfer case may develop an oil leak from the front input shaft bearing retainer or the idler pulley bearing retainer.<br /> |
| IK1600257 | INTERNATIONAL | INTERNATIONAL | 9999 | HX Cluster Gauges not Zeroing at key-off; Only models with cluster P/N 4093442C9, 4093443C9, or 4093444C9*<br /> |
| IK0900135 | INTERNATIONAL | WORKSTAR | 2020 | WorkStar Hybrid Mount to Pad Mount A/C Compressor Retrofit<br /> |
| IK1600255 | INTERNATIONAL | MV | 2020 | Incorrect Turn Signal Cancellation Feature<br /> |
| IK1201446 | INTERNATIONAL | RH | 2020 | A26 Engine fault code SPN: 4364 FMI: 18 Supplemental Diagnostics; Only models built with A26 engine<br /> |
| IK0800550 | INTERNATIONAL | RH | 2020 | Multi Module Programming Information for In-Cab Modules<br /> |
| IK1200818 | INTERNATIONAL | N9 - ENGINE | 2012 | Oil Ingestion (intake) - Component Inspection and CAC cleaning procedure<br /> |
| IK1200753 | INTERNATIONAL | N9 - ENGINE | 2012 | Hydrocarbon Injector Housing Cleaning Procedure (AFI Plugging)<br /> |
| IK1200481 | INTERNATIONAL | N9 - ENGINE | 2012 | Aftertreatment Soot Level Reset After AFI, DPF or DOC Cleaning or Replacement<br /> |
| IK1200431 | INTERNATIONAL | LONESTAR | 2006 | Cummins Ambient Air Temperature (AAT) Sensor Located Rear of Vehicle; Only models with Cummins ISX or ISM engines<br /> |
| IK1200416 | INTERNATIONAL | DURASTAR | 2008 | Dual Throttle Pedal Harness Troubleshooting; only models with Dual Throttle Harness and Switch Installed.<br /> |
| IK1100025 | INTERNATIONAL | LONESTAR | 2013 | Clutch Service Information; only models with Hydraulic Clutch Systems<br /> |
| IK0800418 | INTERNATIONAL | PROSTAR | 2013 | Additional hardware is required when replacing Tail Light Assemblies from Truck-Lite to Weldon; only ProStar models with tail light part numbers 37079 |
| IK0800369 | INTERNATIONAL | LONESTAR | 2006 | Cummins Active Fault Code 249 / 256 Ambient Air Temperature Sensor; only models with Cummins ISX or ISM engines<br /> |
| IK0800284 | INTERNATIONAL | PROSTAR | 2013 | Ambient Air Temperature (AAT) senor faults; only models with 2010 EPA MaxxForce 11, 13 engines.<br /> |
| IK0800223 | INTERNATIONAL | DT466 | 2006 | Accelerator Position Sensor/Idle Validation Switch APS / IVS Diagnostics DLCII equipped engine control systems<br /> |
| IK0800074 | INTERNATIONAL | DURASTAR | 2008 | Dual Drive Cab Throttle Position Harness for Converting Models to both Left and Right Hand Drive<br /> |
| AFC13910 | INTERNATIONAL | PROSTAR | 2013 | Blower Motor Assemblies and Linear Power Module (LPM) Updates.<br /> |
| IK1600257 | INTERNATIONAL | HX | 2020 | HX Cluster Gauges not Zeroing at key-off; Only HX series trucks with cluster P/N 4093442C9, 4093443C9, or 4093444C9<br /> |
| IK0900138 | INTERNATIONAL | HX | 2021 | HX X15 Idler Pulley Bracket Torque Procedure; Only HX series trucks with Cummins X15 engine<br /> |
| IK0900137 | INTERNATIONAL | HX | 2020 | HX Radiator Debris Damage; only HX series trucks built before 1/13/2020<br /> |
| IK0900135 | INTERNATIONAL | WORKSTAR | 2019 | WorkStar Hybrid Mount to Pad Mount A/C Compressor Retrofit; only models with Cummins ISB 6.7 engine.<br /> |
| IK0800587 | INTERNATIONAL | LT | 2020 | Lytx Video Monitoring Camera Inoperative; only LT series equipped with Lytx Camera System<br /> |
| IK0800586 | INTERNATIONAL | CV | 2020 | CV Series Keys;how to prepare a new key blank. The CV key style is different from all other International truck keys.<br /> |
| IK1600251 | INTERNATIONAL | LONESTAR | 2020 | Water Leaks Past Plastic Vapor Barrier Sheet in the Inner Cavity of the Cab Entry Door<br /> |
| IK1600207 | INTERNATIONAL | LONESTAR | 2020 | Wind noise at upper side of cab door due to door out of alignment<br /> |
| IK1500085 | INTERNATIONAL | LT | 2020 | LT / ProStar Fuel Tank Unable to Fill; only sleeper models<br /> |
| IK0800584 | INTERNATIONAL | LONESTAR | 2020 | Auxiliary Engine Speed Control Cannot Hold Engine Speed When Using Steering Wheel Switches<br /> |
| IK1300174 | INTERNATIONAL | LONESTAR | 2020 | Power Take Off (PTO) Programming on LT, RH and LoneStar Models with the Eaton Endurant¿ Transmission; only models with feature code 13GZD, 13GY |
| IK1700018 | INTERNATIONAL | CV | 2020 | CV Vibration - wheels<br /> |
| IK1600245 | INTERNATIONAL | LONESTAR | 2020 | Cab Door Latch Stuck, Door will not open<br /> |
| IK1500085 | INTERNATIONAL | LT | 2020 | LT / ProStar Fuel Tank Unable to Fill; only sleeper models<br /> |
| IK1300159 | INTERNATIONAL | LT | 2020 | Fuller Advantage Series Transmission Power and Ground<br /> |
| IK1201441 | INTERNATIONAL | RH | 2020 | Identifying the Source of Oil Seen at the Lower Flywheel Housing Area. Only models equipped with Allison Transmission and International A26 or Cummins |
| IK1100032 | INTERNATIONAL | RH | 2020 | LT, RH- Hydraulic Clutch Routing and Clipping<br /> |
| IK0800533 | INTERNATIONAL | 5600I | 2006 | Key Codes and Key Cutting Information (Not for CV Series)<br /> |
| IK1600258 | INTERNATIONAL | 4400 | 2003 | Cleaning and Disinfecting Trucks and Buses<br /> |
| IK1200753 | INTERNATIONAL | N9 - ENGINE | 2012 | Hydrocarbon Injector Housing Cleaning Procedure (AFI Plugging)<br /> |
| IK1200722 | INTERNATIONAL | HT570 | 2006 | Misfire Diagnostics with the Cylinder Performance Analyzer (CPA) Tool<br /> |
| IK1200655 | INTERNATIONAL | N9 - ENGINE | 2012 | Injection Pressure Regulator (IPR) Pigtail<br /> |
| IK1200643 | INTERNATIONAL | N10 - ENGINE | 2012 | Freeze Frame Fault Data; only MaxxForce Engines with OBD Diagnostics<br /> |
| IK1200619 | INTERNATIONAL | DURASTAR | 2006 | Injector Driver Module (IDM) Bottom Kit<br /> |
| IK1200516 | INTERNATIONAL | N9 - ENGINE | 2012 | Diagnostic Trouble Codes DTC<br /> |
| IK1200378 | INTERNATIONAL | N9 - ENGINE | 2009 | Service Engine Calibration for Active Aftertreatment Regeneration During PTO ( Engine Speed Control) Operation<br /> |
| IK1200084 | INTERNATIONAL | N9 - ENGINE | 2012 | Auxiliary Engine Speed Control On MaxxForce Engines; Models with Feature Code 12VZA.<br /> |
| IK0800414 | INTERNATIONAL | TERRASTAR | 2010 | Power Windows Stop Randomly or are Inoperative, Power Door Locks are inoperative<br /> |
| IK0800395 | INTERNATIONAL | TRANSTAR | 2013 | Linde Trucks with Advanced Logic used to operate the PTO; only models ownwe and operated by Linde<br /> |
| IK0800393 | INTERNATIONAL | 9900 | 2012 | Voltage gauge and or all cluster gauges freeze<br /> |
| 19516 | INTERNATIONAL | LT | 2020 | Engine Control Module (ECM) calibration update to reduce a false positive Malfunction Indicator Lamp (MIL) for Oxides of Nitrogen (NOx) values when th |
| 19515 | INTERNATIONAL | LT | 2020 | Replacement of the Charge Air Cooler (CAC) outlet hose to prevent a potential increase of particulate matter emissions from a potential hose failure.< |
| 19112 | INTERNATIONAL | CV | 2020 | The Aftertreatment (AFT) harness may be improperly routed and under certain conditions, the cab may contact the AFT harness resulting in chafed or dam |
| 19518 | INTERNATIONAL | MV | 2020 | On certain trucks equipped with an automatic transmission, if the automatic transmission is still in drive or reverse position and the stationary PTO |
| 19116 | INTERNATIONAL | HV | 2020 | The Remote Power Module (RPM) data link circuit may be pinned incorrectly, resulting in potential PTO operation issues.<br /> |
| 19115 | INTERNATIONAL | CV | 2019 | Confirmation that the Vehicle Emission Label has been installed on the driver-side door frame and the Engine Emission Labels have been installed on th |
| IK0900136 | INTERNATIONAL | LT | 2020 | LT Charge Air Cooler Hose Identification<br /> |
| IK0900135 | INTERNATIONAL | WORKSTAR | 2020 | WorkStar Hybrid Mount to Pad Mount A/C Compressor Retrofit; only models with Cummins ISB 6.7 engine<br /> |
| IK0800080 | INTERNATIONAL | CV | 2020 | J1939 Data Link Troubleshooting<br /> |
| 20101 | INTERNATIONAL | LT | 2020 | Certain tandem axle International HX and LT Series trucks built between 20 August 2019 and 17 December 2019 with a lift axle may require the ABS Stabi |
| DAN-D4V6K-01 | INTERNATIONAL | INTERNATIONAL | 9999 | This is a communication from Dana to Navistar identifying a potential non-conformance in supplied bearing cups due to a possible through hardness cond |
| IK0400152 | INTERNATIONAL | RH | 2020 | Windshield Replacement on trucks equipped with Lane Departure Cameras; Only RH, LT, and Medium duty with feature codes 008TTG, 0008TPU, 0008TTT, 0008T |
| 19114 | INTERNATIONAL | HV | 2020 | Torque Converter parameter setting may have been programmed incorrectly at time of manufacture. Only Heavy duty HV and all HX.<br /> |
| IK1900257 | INTERNATIONAL | LONESTAR | 2020 | Day Cab Roof Air Deflector Vibrates against Cab Roof; only models with P/N 4067947C92 Roof Air Deflector<br /> |
| IK1900198 | INTERNATIONAL | PROSTAR | 2016 | MaxxPower No Idle Battery-Powered A/C System Diagnostic Guide; Only sleeper cab models with feature code 16UZL<br /> |
| MIN13105 | INTERNATIONAL | PROSTAR | 2013 | Air Compressor Replacement for Certain Vehicles with MaxxForce 13 Engines.<br /> |
| IK1900198 | INTERNATIONAL | PROSTAR | 2013 | MaxxPower No Idle Battery-Powered A/C System Diagnostic Guide; models equipped with feature 16UZL<br /> |
| IK1900172 | INTERNATIONAL | PROSTAR | 2013 | Espar Heater Diagnostic Guide; only vehicles with feature code 16UZL, 16VTV (Airtronic D2 Heater, Hydronic D5 Heater)<br /> |
| IK1600179 | INTERNATIONAL | TERRASTAR | 2013 | Interior door handle seal<br /> |
| IK1600176 | INTERNATIONAL | INTERNATIONAL | 9999 | Lockset Instructions for Key Code Information on Packaging; only All keycode sets ordered through Navistar Parts system<br /> |
| IK1600149 | INTERNATIONAL | TERRASTAR | 2010 | One piece sunshade mounting bracket becomes loose or comes off the cab; Only models built in Garland or Springfield between June 2010 and February 201 |
| IK1600096 | INTERNATIONAL | CF500 | 2007 | Front cab mount bushings<br /> |
| IK1500041 | INTERNATIONAL | INTERNATIONAL | 9999 | Customer Tip Card - ULSD Fuel System Impacts<br /> |
| IK1300134 | INTERNATIONAL | TERRASTAR | 2010 | TerraStar Transmission Shift Cable Routing<br /> |
| IK1300133 | INTERNATIONAL | INTERNATIONAL | 9999 | Manual Transmission With External Oil Cooler Refilling Procedure<br /> |
| IK1200894 | INTERNATIONAL | N10 - ENGINE | 2012 | Aftertreatment Service: A properly operating aftertreatment system requires little manual intervention from the operator. DPF Lamps that are illuminat |
| IK1200893 | INTERNATIONAL | N9 - ENGINE | 2012 | Oil Filter Cap and Bypass Valve Assembly<br /> |
| IK1200892 | INTERNATIONAL | N9 - ENGINE | 2009 | EGR Valve Identification / Adjustment Procedure DTC6259<br /> |
| IK1200891 | INTERNATIONAL | N9 - ENGINE | 2012 | Service Engines with the aftermarket Thermal Management Valve; only Service Engine P/N: 7080062C92, 7080063C92, 7091736C92<br /> |
| IK1200888 | INTERNATIONAL | N9 - ENGINE | 2012 | Exporting Vehicle Trip Report Data with Servicemaxx<br /> |
| IK1200855 | INTERNATIONAL | N9 - ENGINE | 2011 | Eliminate Harness Rubbing at ECM Bracket; only in truck models built prior to 09/01/2012<br /> |
| MIN13103 | INTERNATIONAL | WORKSTAR | 2013 | The vehicles involved in this campaign were released from the plants with engines having an incorrect EPA emissions label.<br /> |
| IK1600177 | INTERNATIONAL | PROSTAR | 2013 | SkyRise Roof Replacement<br /> |
| IK1600176 | INTERNATIONAL | INTERNATIONAL | 9999 | Lockset Instructions for Key Code Information on Packaging; only All keycode sets ordered through Navistar Parts system<br /> |
| IK1300094 | INTERNATIONAL | 9900 | 9999 | Meritor Wabco Diagnostic and Service Guides<br /> |
| IK1300086 | INTERNATIONAL | WORKSTAR | 2009 | Bendix Stability Control -Customer Satisfaction Performance Improvement on specific Emergency/Tanker applications; Only models built From March 2009 t |
| IK1200888 | INTERNATIONAL | N9 - ENGINE | 2012 | Exporting Vehicle Trip Report Data with Servicemaxx<br /> |
| IK1200883 | INTERNATIONAL | N9 - ENGINE | 2012 | Exhaust Manifold Seal Clamps<br /> |
| IK1200844 | INTERNATIONAL | N9 - ENGINE | 2012 | SPN 190 FMI 0 Engine Over-speed most severe level<br /> |
| IK1200818 | INTERNATIONAL | N9 - ENGINE | 2012 | Oil Ingestion (intake) - Component Inspection and CAC cleaning procedure<br /> |
Subscribe for our latest newslatters
Know if there is a safety problem with your vehicles, tires or car seat, and how to get it fixed.